NETGEAR Nighthawk X4S Smart Wifi Router (R7800) - AC2600 Wireless Speed (up to 2600 Mbps) | Up to 2500 sq ft Coverage & 45 Devices | 4 x 1G Ethernet, 2 x 3.0 USB, and 1 x eSATA ports

Product Information

Four antennas protrude from the Nighthawk X4S, giving it an imposing look, and the unit is fairly large overall. The X4S is perhaps a little less bonkers-looking than the D-Link DIR-890L AC3200, but it’s clear that these two high-end routers are aiming for the roughly same market. I have not verified that there is similar "use real world randomness" patch also for ath10k, but I suppose that there is one... ( @nbd likely knows that best) ieee80211_ioctl_setparam-5962, IEEE80211_PARAM_NR_SHARE_RADIO_FLAG, MAX_RADIO_CNT = 2sysinit: watchdog: /dev/watchdog: Device or resource busy We wish this was an easier process. Router updates are one of the most critical things you can do to keep your computers, smartphones, gaming consoles, smart-home devices and personal information safe. Someday all router makers will understand that. All Netgear home networking devices that need to install the March 2020 firmware updates

As part of the Netgear Nighthawk X4S’s setup, you also receive the option to install Netgear Genie – desktop management software. It’s available as an iPhone/Android app too. The case bottom and cover are attached to each other pretty tightly, but the case can be opened once you figure out all necessary steps: snd 38575 8 snd_soc_core,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer,snd_rawmidi,snd_seq_device,snd_hwdep Linux version 3.4.103 (li.zhang@team-3) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 SMP Mon Dec 10 11:05:40 UTC 2018Recommended configuration (build is the master defaults (CPU has been further optimized as per below), you’ll have to do all the rest yourself): ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 I use currently tftpd64 GUI tool from jounin. tftp2 tool (from dd-wrt) used to work earlier, but for some reason does not work with the current master images.) Optionally you can use on demand settings (some report less stability): echo ondemand > /sys/devices/system/cpu/cpufreq/policy0/scaling_governor

The first thing you need to do is ensure that your router is compatible. Head to the DD-WRT database, then type in theexactmodel number of your router. This database will tell you your router is one of four things: In computer networking, the maximum transmission unit ( MTU) is the size of the largest protocol data unit (PDU) that can be communicated in a single network-layer transaction. The MTU relates to but is not identical to the maximum frame size that can be transported on the data link layer, e.g. Ethernet frame.The R7800 supports NETGEAR’s standard genie feature set and user interface, as shown below. As far as I could tell, all the usual features were there, including OpenVPN support. bootcmd=sleep 2; nmrp; if loadn_dniimg 0 0x1480000 0x44000000 && chk_dniimg 0x44000000; then bootipq2; else fw_recovery; fi The serial header can be seen through the left ventilation grill, so it might be possible to get access to it without by opening the case, by cutting a hole to the ventilation grill on the side panel.) My diffconfig file is set up for ath10k-ct driver/firmware. If you want to use ath10k driver/firmware instead - use the diffconfig-ath10k file.